Repairing Minor Deterioration Of Brass Features

Technical Procedures Disclaimer

Prior to inclusion in GSA’s library of procedures, documents are reviewed by one or more qualified preservation specialists for general consistency with the Secretary of Interior Standards for rehabilitating historic buildings as understood at the time the procedure is added to the library. All specifications require project-specific editing and professional judgement regarding the applicability of a procedure to a particular building, project or location. References to products and suppliers are to serve as a general guideline and do not constitute a federal endorsement or determination that a product or method is the best or most current alternative, remains available, or is compliant with current environmental regulations and safety standards. The library of procedures is intended to serve as a resource, not a substitute, for specification development by a qualified preservation professional.

Rewrite

We’ve reviewed these procedures for general consistency with federal standards for rehabilitating historic buildings and provide them only as a reference. Specifications should only be applied under the guidance of a qualified preservation professional who can assess the applicability of a procedure to a particular building, project or location. References to products and suppliers serve as general guidelines and do not constitute a federal endorsement nor a determination that a product or method is the best alternative or compliant with current environmental regulations and safety standards.

PART 1---GENERAL

1.01 SUMMARY

  1. This procedure includes guidance on repairing metal which suffers from dents, scratches, small holes or nicks; and treating other minor damage on architectural metals commonly found in historic buildings. Significant metal elements, sculptural bronze as example, require the care of a qualified conservator.
    1. For guidance on cleaning, polishing and removing corrosion from metal, see 05010-01-P.
    2. For general information on the characteristics, uses and problems associated with metal, see 05010-03-S.
  2. Safety Precautions:
    1. Workers should take precautions to prevent epoxies and their components from contacting the skin.
    2. Provide protective clothing which must be worn and protective creams for exposed skin areas. Accidental contact with unprotected skin to these materials must be treated immediately by washing with soap and water, never with solvents.
    3. Exercise care to avoid skin contact to tool cleaning solvents and to provide adequate ventilation for clean-up operations.
  3. See 01100-07-S for general project guidelines to be reviewed along with this procedure. These guidelines cover the following sections:
    1. Safety Precautions
    2. Historic Structures Precautions
    3. Submittals
    4. Quality Assurance
    5. Delivery, Storage and Handling
    6. Project/Site Conditions
    7. Sequencing and Scheduling
    8. General Protection (Surface and Surrounding)

These guidelines should be reviewed prior to performing this procedure and should be followed, when applicable, along with recommendations from the Regional Historic Preservation Officer (RHPO).

1.02 SUMMARY DESCRIPTION

  1. This procedure is for repair of minor surface weathering or damage on otherwise sound architectural metals.

PART 2---PRODUCTS

2.01 MATERIALS

  1. Epoxy such as one of the following:
    1. Auto body putty - available from auto body stores, or from hardware stores.
      -OR-
    2. Resin-impregnated fiberglass. Fiberglass comes in\mesh or strands (mesh is best for small holes) - available from marine supply stores.
      -OR-
    3. Polyester or epoxy resin, such as Tnemec Series 215-Surfacing Epoxy. (a modified polyamine epoxy), or approved equal - available in cans from marine supply stores.
  2. Clean, soft wiping cloths

2.02 EQUIPMENT

  1. Eye and skin protection
  2. Gloves and protective gear
  3. Stiff bristle brushes
  4. Hammer

PART 3---EXECUTION

3.01 EXAMINATION

  1. Before proceeding with steps to repair the metal, first examine the surface(s) to determine the extent of the work required. Document with description and photos the existing conditions prior to treatment. Look for:
    1. Wear - especially moving parts.
    2. Broken, cracked, missing distorted, or loose parts.
    3. Coating failures such as chips, peeling, checks, bubbling, and wear.
    4. Rust corrosion - caused by moisture, deicing salts, acids, soils, gypsum plasters, magnesium oxychloride cements, ashes, clinkers, and sulfur compounds. Determine the source of the moisture which causes the deterioration.

3.02 ERECTION, INSTALLATION, APPLICATION

  1. For perforated spots and thinned surrounding areas: Soft solder with a patch large enough, and cut appropriately, to cover the entire area. See 05010-07-R for guidance on soldering.
  2. For Dents and Scratches:
    1. If the backside of metal feature is accessible and not too thick, gently hammer the dent back in place.
    2. For severely damaged sections, cut out, recast, and reattach by riveting or brazing. Brazing is a form of soldering that uses a bronze or brass filler metal.
    3. Buff scratches to match the original finish and texture. See 05010-01-P.
  3. For Small Holes, Nicks, and Minor Imperfections in Painted Metal:
    1. Clean the metal surface of any dirt, grease or corrosion. See 05010-01-P for guidance.
    2. Prime metal before applying epoxy, and allow to dry.
    3. Fill damaged areas with an epoxy patching compound.
      NOTE: EPOXY USED SHOULD BE COMPATIBLE WITH ANY PAINTS, LACQUERS OR WAXES USED.
      1. Mix and apply epoxy according to manufacturers instructions.
      2. Allow to cure and dry thoroughly.
        NOTE: EPOXY SHOULD CURE TO A SMOOTH FINISH, REQUIRING NO FURTHER SANDING OR GRINDING.
    4. Apply a second coat of primer.
    5. Apply finish coat of paint to the epoxy patch area.
    6. If the metal piece cannot be salvaged, it should be replaced with new similar metal or other inert replacement material (as example: bronze plated) of the same weight, configuration, and temper hardness. RHPO MUST APPROVE REPLACEMENT.
  4. Missing pieces: Missing pieces can be reproduced by casting.
  5. Project Closeout: Document the treatment results with description and photographs for building files.