Removing Surface Dirt From Concrete

Technical Procedures Disclaimer

Prior to inclusion in GSA’s library of procedures, documents are reviewed by one or more qualified preservation specialists for general consistency with the Secretary of Interior Standards for rehabilitating historic buildings as understood at the time the procedure is added to the library. All specifications require project-specific editing and professional judgement regarding the applicability of a procedure to a particular building, project or location. References to products and suppliers are to serve as a general guideline and do not constitute a federal endorsement or determination that a product or method is the best or most current alternative, remains available, or is compliant with current environmental regulations and safety standards. The library of procedures is intended to serve as a resource, not a substitute, for specification development by a qualified preservation professional.

Rewrite

We’ve reviewed these procedures for general consistency with federal standards for rehabilitating historic buildings and provide them only as a reference. Specifications should only be applied under the guidance of a qualified preservation professional who can assess the applicability of a procedure to a particular building, project or location. References to products and suppliers serve as general guidelines and do not constitute a federal endorsement nor a determination that a product or method is the best alternative or compliant with current environmental regulations and safety standards.

PREFACE: The cleaning or removal of stains from concrete may involve the use of liquids, detergents or solvents which may run off on\ adjacent material, discolor the concrete or drive the stains deeper into porous concrete. Use the products and techniques described here only for the combinations of dirt/stain and concrete specified.

PART 1---GENERAL

1.01 SUMMARY

  1. This procedure includes guidance on removing dirt from concrete using a detergent, chemical solvent or steam.
  2. Dirt encompasses deposits of almost any material in a location where it's not wanted, but it usually includes fine, dark-colored solid particles, often surrounded by some kind of oily film. It is particularly troublesome on architectural and decorative concrete, including exposed aggregate surfaces.
  3. Safety Precautions:
    1. DO NOT save unused portions of stain-removal materials.
    2. DO NOT store any chemicals in unmarked containers.
    3. EXCELLENT VENTILATION MUST BE PROVIDED WHEREVER ANY SOLVENT IS USED. USE RESPIRATORS WITH SOLVENT FILTERS.
    4. Whenever acid is used, the surface should be thoroughly rinsed with water as soon as its action has been adequate. Otherwise it will continue etching the concrete even though the stain is gone.
    5. Provide adequate clothing and protective gear where the chemicals are indicated to be dangerous.
    6. Have available antidote and accident treatment chemicals where noted.
  4. See "General Project Guidelines" for general project guidelines to be reviewed along with this procedure. These guidelines cover the following sections:
    1. Safety Precautions
    2. Historic Structures Precautions
    3. Submittals
    4. Quality Assurance
    5. Delivery, Storage and Handling
    6. Project/Site Conditions
    7. Sequencing and Scheduling
    8. General Protection (Surface and Surrounding)
      These guidelines should be reviewed prior to performing this procedure and should be followed, when applicable, along with recommendations from the Regional Historic Preservation Officer (RHPO).

PART 2---PRODUCTS

2.01 MATERIALS

NOTE: Chemical products are sometimes sold under a common name. This usually means that the substance is not as pure as the same chemical sold under its chemical name. The grade of purity of common name substances, however, is usually adequate for stain removal work, and these products should be purchased when available, as they tend to be less expensive. Common names are indicated below by an asterisk (*).

  1. Hydrochloric Acid:
    1. A strong corrosive irritating acid.
    2. Other chemical or common names include Chlorhydric acid; Hydrogen chloride; Muriatic acid*; Marine acid*; Spirit of salt*; Spirit of sea salt*.
    3. Available from chemical supply house, drugstore, hardware store.
  2. Detergent:
    1. CAUTION: SOME DETERGENTS CONTAIN AMMONIA AND MAY REACT VIGOROUSLY WITH HYDROCHLORIC ACID.
  3. Clean, potable water
  4. Clean white cloths or towels

2.02 EQUIPMENT

  1. Steam cleaning equipment
  2. Stiff bristle brushes (non-metallic)

PART 3---EXECUTION
3.01 PREPARATION

  1. Protection:
    1. Provide adequate wash solutions (i.e. water, soap and towels) before starting the job.
    2. Whenever acid is used, the surface should be thoroughly rinsed with water as soon as its action has been adequate. Otherwise it will continue etching the concrete even though the stain is gone.

3.02 ERECTION, INSTALLATION, APPLICATION

NOTE: DO NOT TRY MORE THAN ONE TREATMENT ON A GIVEN AREA UNLESS THE CHEMICALS USED FROM PRIOR TREATMENT HAVE BEEN WASHED AWAY.

  1. Brush affected area with water and strong detergent.
  2. Rinse the area thoroughly with clean, clear water and blot the surface dry with clean towels.
  3. Repeat the treatment as necessary until the desired level of cleanliness is achieved.
    -OR-
  4. Mix 1 part hydrochloric acid in 19 parts water.
  5. Scrub the concrete surface with this solution. NOTE: THIS IS A STRONG METHOD AND MAY ROUGHEN THE CONCRETE.
  6. Rinse the area thoroughly with clean, clear water, blot the surface dry with clean towels.
  7. Repeat the treatment as necessary until the desired level of cleanliness is achieved.
    -OR-
  8. Steam cleaning is generally effective and may be used in combination with proprietary materials, such as detergents for dirt removal.
  9. If there is oil present in the dirt, follow the procedure described for removing lubricating oil, see 03710-31-R "Poulticing Lubricating and Petroleum Oil Stains From Concrete".