Patching Large Holes In Plaster With Sheetrock

Procedure code:
920012S
Source:
Developed For Hspg (Nps - Sero)
Division:
Finishes
Section:
Lath & Plaster
Last Modified:
07/23/2015


PATCHING LARGE HOLES IN PLASTER WITH DRYWALL

(NOTE: various names are used for the same manufactured product including: drywall, plasterboard, wall board, gypsum board;

and there there are further names for modified drywall and proprietary products with trademarked names)


PART 1---GENERAL

1.01 SUMMARY

A. This procedure includes guidance on patching holes in
wall plaster larger than 4 inches in diameter. When
large sections of plaster are missing, drywall patches
can be used as a base.

B. See 01100-07-S for general project guidelines to be
reviewed along with this procedure. These guidelines
cover the following sections:

1. Safety Precautions

2. Historic Structures Precautions

3. Submittals

4. Quality Assurance

5. Delivery, Storage and Handling

6. Project/Site Conditions

7. Sequencing and Scheduling

8. General Protection (Surface and Surrounding)

These guidelines should be reviewed prior to performing
this procedure and should be followed, when applicable,
along with recommendations from the Regional Historic
Preservation Officer (RHPO).


PART 2---PRODUCTS

2.01 MATERIALS

A. Drywall and joint compound

B. Nails and screws

C. Joint tape (cloth mesh preferred)

2.02 EQUIPMENT

A. 6 inch taping knife

B. 12 inch taping knife

C. Float

D. Hawk

E. Sanding sponge (medium fine grit)

F. Stiff putty knife

G. Goggles, work gloves, and dust mask

H. Hammer and cold chisel

I. Needlenose pliers and wire cutter

J. Screwgun and drill

K. Spray bottle and drop cloths

L. Tin snips

M. Vacuum


PART 3---EXECUTION

3.01 EXAMINATION

A. Determine the extent of damaged plaster. Look for:

1. Holes.

2. Water Stains: Brownish rings on the plaster,
especially the ceilings, indicate that the plaster
has been wet. If the water was stopped quickly,
the surface may only need to be sealed with
pigmented shellac to prevent the stain from
bleeding through the new paint or wallpaper.
However, if the leak continued for a long period,
the plaster may need to be replaced, and will often
have a powdery appearance.

3. Chipping, flaking and delamination of plaster due
to water infiltration.

3.02 ERECTION/INSTALLATION/APPLICATION

A. Removing Deteriorated Plaster:

1. Wear a dust mask, goggles and gloves and pull loose
plaster from the walls with your hands (a flat
prybar may also be helpful in removing plaster that
is difficult to remove by hand).

2. To remove sound plaster, for whatever reason, drill
holes in the line of your cut with a carbide drill
bit; Holding the chisel at a shallow angle,
carefully cut directly from hole to hole with a
cold chisel; Cut the resulting plaster free from
the lath by chipping the keys from the side.

3. Cut the plaster back to the nearest studs to make a
regular opening, and re-secure the lath with
drywall nails.

4. Use plaster washers and wood screws to re-secure
weakly-keyed areas of sound plaster to the wall or
ceiling.

5. Knock any plaster stuck between the lath back into
the wall cavity.

6. Vacuum all dust, loose plaster, and other debris
from the hole with a shop-vac, or sweep it out with
an old paintbrush.

B. Making a drywall patch:

1. Shim the drywall as required to bring it up flush
with the surface of the adjacent plaster.

2. Cut a drywall patch to fit neatly in the opening.

3. Nail or screw the drywall in place; Nailheads or
screwheads should be set slightly below the surface
of the drywall, but without breaking the paper.

4. Using the 6 inch taping knife, fill the joint
between the drywall and the plaster with a small
amount of joint compound.

5. Apply a fairly smooth, heavy coat of compound over
the joint a little wider than the tape width.

6. Center the joint tape over the length of the joint;
Hold the 6 inch taping knife at a 45 degree angle
and press the tape into the compound; Smooth out
any air pockets under the tape.

7. Apply a thin layer of compound over the tape and
apply a first coat of compound to nails or screws.

8. Knock off any ridges or pimples that develop from
shrinkage and cracking in the compound.

9. Apply the second coat of compound with the 6 inch
taping knife and feather the edges out 6-8 inches;
Scrape off any ridges or bumps.

10. When the second coat is dry, apply the third coat
of compound with the 12 inch taping knife and
feather the edges out 12-14 inches.

11. Touch up low spots with additional compound or high
spots by light sanding with a wet sanding sponge.


print Share Icon Last Reviewed 2017-11-30