Reattaching Loose Or Fallen Tin Ceiling Panels

Procedure code:
954501S
Source:
Ohj - November/December 1987
Division:
Finishes
Section:
Special Ceiling Surfaces
Last Modified:
11/19/2014


REATTACHING LOOSE OR FALLEN TIN CEILING PANELS


PART 1---GENERAL

1.01 SUMMARY

A. This procedure includes guidance on resecuring tin
ceiling panels that have worked loose or have fallen.

B. Metal ceiling panels are typically 2'-0" x 8'-0" and are
nailed to wood furring strips which are, in turn, nailed
to the ceiling joists of an existing ceiling.


PART 2---PRODUCTS

2.01 MANUFACTURERS

NOTE: The following manufactuers listed below are potential
sources for replacement panels, where existing panels can not
be reattached.

A. W.F. Norman Corporation
wfnorman.com


B. Classic Ceilings
www.classicceilings.com

C. Entol Industries, Inc.
www.entol.com

2.02 MATERIALS

A. 1" long flat head nails as required

B. 3" long flat head nails or 2-1/2" drywall screws as
required

C. Wood shims as required

D. Glazing compound or latex caulk

2.03 EQUIPMENT

A. Hammer and/or screwgun

B. Heavy gloves and protective gear

C. Scaffolding/working platforms

D. Ladders


PART 3---EXECUTION

3.01 EXAMINATION

NOTE: BEFORE RESECURING ANY CEILING PANELS OR FURRING STRIPS,
IT MAY BE USEFUL TO UNDERSTAND HOW A METAL CEILING IS
ASSEMBLED.

A. Tin ceiling panels are typically 2'-0" x 8'-0" and are
attached to an existing ceiling by nailing the panels to
1"x2" furring strips.

B. 1"x2" furring strips are typically attached to an
existing ceiling using 3" flat head nails or 2-1/2"
drywall screws.

NOTE: FURRING STRIPS MAY BE SHIMMED AT VARIOUS LOCATIONS
TO ENSURE THAT THE CEILING WILL BE AS LEVEL AS POSSIBLE.

1. Furring strips are first nailed perpendicular to
the ceiling joists and spaced 24" on center.

2. Additional 1"x2" furring strips are then installed
parallel with the ceiling joists (and perpendicular
to the furring strips installed in #1 above) and
spaced 8'-0" on center to provide nailers where the
ceiling panels overlap. These secondary furring
strips are typically 22" long (if 2" furring is
used).

3. Finally, intermediate furring strips are nailed
perpendicular to the ceiling joists (as in #1
above) to make the overall spacing of furring
strips in this direction 12" on center. These
intermediate strips are typically 94" long (if 2"
furring is used).

4. 2'-0" x 8'-0" ceiling panels are then nailed to the
furring strips in an overlapping position using 1"
flat head nails.

3.02 ERECTION, INSTALLATION, APPLICATION

A. Check for loose or missing nails used to attach the
ceiling panels to the furring strips.


1. Hammer nails securely back in place as required.

2. Replace missing nails with 1" flat head nails.
Nail at beads/buttons along furring strips as
required to resecure the panel.

B. For panels that have fallen: Check to see that the
furring strips are level and secure; check to see that
wood shims are still securely in place.

1. Shim behind the furring strips as needed before
nailing to level it with the rest of the strips.

a. Use a good straightedge to align the strips.

b. Use the claw of a hammer to pull high strips
down into the same plane as the lower strips.

c. Install shims between the furring and the
ceiling as required.

2. When the strip is in line, drive all nails home
using 3" flat head nails.

3. Reattach tin panel to furring strips as described
above in Section A.

a. Drive the nails to one side of the bead.

b. To line up the next sheet, overlap the beads
with the previous sheet (the way a ball and
socket fit). Nail directly through the beads
on the overlapping sheet.

C. For gaps where edges of panels overlap:

1. Hold the flat head of a 3" nail against the edge of
the metal and gently tap the tip of the nail with a
hammer.

2. Fill any remaining gaps with glazing compound or
latex caulk.


print Share Icon Last Reviewed 2017-11-30